Tłumaczenie - Norweski-Angielski - De borrene DT5040 er for lange for kunden.Kunden...

Obecna pozycja ‎Tłumaczenie

Ten tekst jest dostępny w następujęcych językach:

Kategoria List / Email

Tytuł

De borrene DT5040 er for lange for kunden.Kunden...

Tekst
Wprowadzone przez

dewalt2008

Język źródłowy: Norweski

De borrene DT5040 er for lange.Kunden Ã¸nsker de samme stÃ¸rrelsene som pÃ¥ Dormer bor. Dvs de som vi har sendt hendvendelse pÃ¥ tidligere.

Kan vi produsere en bor i 10,5mm med arbeidslengde pÃ¥ 15mm og totallengde ca 35mm, borrene skal brukes pÃ¥ syrefast stÃ¥l. Antall ca 300 bor.

HÃ¥per dere kommer tilbake raskt pÃ¥ dette, da det haster for min kunde.

Tytuł

The drills DT5040 are too long. The customer

Tłumaczenie

Angielski

Tłumaczone przez

pias

Język docelowy: Angielski

The drills DT5040 are too long. The customer wishes to have the sizes as on Dormer drill. I.e. the ones that we sent a letter about earlier.

Can we produce a drill 10,5mm with worklength 15mm and total length approx. 35mm? The drills are to be used on acid proof steel. Quantity approx. 300 drills.

Hope that you will reply fast on this, because it's urgent for my customer.

Ostatnio zatwierdzony albo edytowany przez lilian canale

- 20 Maj 2008 03:08

Ostatni Post

	Autor	Post
		17 Maj 2008 02:27
	lilian canale Liczba postów: 14972	Hi Pia, "because it's in a hurry for my customer." well, you have some options to make this line sound better, you may choose the one that better conveys the original, OK? "because my customer is in a hurry." "because it's urgent to my customer." "because my customer is in urgent need of it."
		17 Maj 2008 09:23
	pias Liczba postów: 8113	Ok, thank you! I'll edit.
		19 Maj 2008 17:48
	Tantine Liczba postów: 2747	Hi Pias, Hi Lilly I have some suggestions for correction: The drills DT5040 is too long. Either: "The drills ... are too long" Or: "The drill ... is too long" The customer wish to have... Either: "The customers wish to have" Or: "The customer wishes Can we produce a drill 10,5mm with worklenght 15mm and total length approx. 35mm, the drills shall be used on acid proof steel. If this is a question there should be a question mark at the end of the phrase. If it is not a question "Can we" should read "We can". "We can produce 10.5mm drill with 15mm worklength ... drills are to be used..." "...because it's urgent for my customer." Hope this helps Bises Tantine
		19 Maj 2008 17:55
	lilian canale Liczba postów: 14972	Thanks Tantine Pia, would you consider editing those suggestions? Then, the job will be perfect!
		19 Maj 2008 18:24
	pias Liczba postów: 8113	Thank you so much Tantine and boss Lilian! I'm happy to have such a good "teachers". I'll edit right away.
		20 Maj 2008 01:15
	Bamsa Liczba postów: 1524	Not so important Accordig to what I have learned at the engineer school, in technical English, Acidproof is one word.
		20 Maj 2008 09:56
	pias Liczba postów: 8113	Thank you Bamsa Anyway, I think that the boss (Lilian) already has accepted it as it was.